MediaWiki API result

{
    "batchcomplete": "",
    "continue": {
        "gapcontinue": "SMT100",
        "continue": "gapcontinue||"
    },
    "warnings": {
        "main": {
            "*": "Subscribe to the mediawiki-api-announce mailing list at <https://lists.wikimedia.org/postorius/lists/mediawiki-api-announce.lists.wikimedia.org/> for notice of API deprecations and breaking changes."
        },
        "revisions": {
            "*": "Because \"rvslots\" was not specified, a legacy format has been used for the output. This format is deprecated, and in the future the new format will always be used."
        }
    },
    "query": {
        "pages": {
            "29": {
                "pageid": 29,
                "ns": 0,
                "title": "SDR2",
                "revisions": [
                    {
                        "contentformat": "text/x-wiki",
                        "contentmodel": "wikitext",
                        "*": "=== Is the free Xilinx ISE webpack provided by Xilinx usable with this SDR-2 kit? ===\n\nNo, it isn't.\n\nThe Xilinx webpack supports only small FPGA devices.\n\nIt is required to use the Xilinx ISE Foundation software to access the SDR-2 Virtex-4 FX60 FPGA devices.\n\n\n=== What software for SDR-2 kit is available under MATLAB? ===\n\nThere are full support from: SMT6040, SMT6041, PARS and even MATLAB/Simulink Real Time Workshop, Simulink HDL-coder and Xilinx System Generator that are fully compatible with the 3L Diamond tools.\n\nOther design approaches are available like \"C-to-FPGA\" compilers like Impulse-C."
                    }
                ]
            },
            "30": {
                "pageid": 30,
                "ns": 0,
                "title": "SLB Mezzanine",
                "revisions": [
                    {
                        "contentformat": "text/x-wiki",
                        "contentmodel": "wikitext",
                        "*": "Every DSP or FPGA application has varying input and output requirements. These can\nbe simple USB interfaces, CameraLink, or high-speed analog I/O. Utilising a standard\nbase module, a flexible system can be tailored by attaching a wide variety of daughter\nmodules. For this reason, the SLB mezzanine concept was introduced.\n\nThis concept consists of a carrier board (often a DSP or FPGA TIM module) which\nincludes a high density connector. This connector accepts a daughter module (or\nmezzanine) which is mounted above the carrier (or in some case can be mounted\nseparately and joined using a flexible cable).\n\nThe SLB connector is of a differential construction (based on a Samtec QSH/QTH-DP\nseries 0.5mm pitch connectors) and characterised for high-speed data of over 1Gb/s per\npin pair.\n\nThe connector is split into three sections, 2 for high-speed differential (LVDS) data\ntransfer, and one for control. A separate connector provides power to the mezzanine\nboard.\n\nBelow are listed the features of the SLB:\n* Low Voltage Differential Signalling (LVDS), supported by Xilinx FPGAs,\n* One control signal port,\n* Two differential data ports,\n* A set of power supplies: +3.3, +5, +12 and \u201312 Volts.\n* Two-extra mounting holes to hold Main/Base and Daughter modules together.\n\nFull information about the SLB Standard can be found in the [http://tinyurl.com/slb-specification SLB (Sundance Local Bus) Specification (PDF)]\n\nListed below is a table of the I/O voltages for various SLB modules.\nThis table will be updated as and when the information becomes available.\n\n<table border=\"1\" width=\"300\">\n<tr>\n       <th>SLB Module</th>\n       <th>I/O Level</th>\n</tr>\n<tr>\n       <td>SMT350</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT381</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT384</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT390</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT391</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT399-160</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT903</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT909</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT911</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT916</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT922</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT939</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT941</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT942</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT943</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT945</td>\n       <td>2.5V Drive or 2.5V/3.3V Receive</td>\n</tr>\n<tr>\n       <td>SMT946</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT949</td>\n       <td>2.5V</td>\n</tr>\n<tr>\n       <td>SMT950</td>\n       <td>3.3V</td>\n</tr>\n<tr>\n       <td>SMT959</td>\n       <td>2.5V</td>\n</tr>\n</table>"
                    }
                ]
            }
        }
    }
}