Lynsyn Lite

About

The Lynsyn Lite is a dual-purpose card for both power measurement and JTAG communications.

It can monitor voltage and current on three independent sensors, with voltage ranges between 0V and 23V and currents between 0A and 5A.

By default, and as supplied for the V3.1 hardware, the sensors are set to be as the table below:

Current Sensor ranges.

Sensor	Current Range	Shunt Resistor	Shunt Size
S1	0 - 5 Amps	R4	0.025 Ohms
S2	0 - 2.5 Amps	R5	0.05 Ohms
S3	0 – 1.25 Amps	R6	0.1 Ohms

When in doubt, user S1 as it has the largest current range, but for developments where the current draw is known to be within the lower ranges, these would be better to use as they would give a more detailed view of currents drawn at different times.

Full information on the Lynsyn Lite can be found here: https://github.com/EECS-NTNU/lynsyn-host-software/wiki

Software Setup

Windows

(https://github.com/EECS-NTNU/lynsyn-host-software/wiki/Installing-on-Windows)

Download the pre-built binaries (executables) of the Lynsyn tools. These can be found here: DOWNLOAD LYNSYN TOOLS V1.3 LINK (https://github.com/EECS-NTNU/lynsyn-host-software/releases)

Unzip the tools to a location on your computer. The software tools are not installed and are just run from within this folder so it can be anywhere, but for ease of use we would suggest C:\lynsyn\.

Install the driver for the card. Connect the Lynsyn Lite to your PC. It gets power over the MicroUSB connection.

Open the Zadig application. Your PC may ask if you want to run it (UAC), you do. It should pop up like this: zadig application

From the “Options” menu, select “List All Devices”. Zadig ListAll

The drop-down box in the middle of the application will now be populated. Open this and select the Lynsyn. Zadig Select Lynsyn

Press the button to Install / Reinstall driver.

This may take a few minutes, please wait till you see the pop up saying that the driver was successfully installed: Zadig Instal Done

The Lynsyn Lite should now be ready to use.




Linux

As there are many variations of Linux, this guide is for Ubuntu 22.04.

1. Open a terminal window and update and upgrade
   sudo apt-get update && sudo apt-get upgrade
2. Install the required dependencies for the Lynsyn project.
   sudo apt install build-essential qtbase5-dev libqt5sql5-sqlite libusb-1.0-0-dev git dbus-x11
3. Clone the GitHub repository to your machine.
   git clone https://github.com/EECS-NTNU/lynsyn-host-software.git
4. Go to the cloned directory
   cd lynsyn-host-software/
5. Run the make (Just type “make” – no inverted commas) file to compile the software. It will look like a lot has gone wrong, but as long as it says “Host software compilation successful” at the end, you are OK.
   make
6. Install the made software by running this command:
   sudo make install Again, it will say a lot, but as long as it shows “Host software compilation successful” and “Software and hardware installed” it is all OK.

You have now built the software packages required for the Lynsyn Lite.

Running the Power Measurement Tools

Windows

Recording a Session

From the command line

1. Open a command prompt window and navigate to C:\Lynsyn (or wherever you saved the tools earlier)
2. To start logging a session you need to use the lynsyn_sampler application.
   

   

   Lynsyn sampler windows

   
   

   For this simple example we will be just setting to run the application for a 30 second session and saving the data to the default “output.csv” file. To run it for longer or shorter, just change the number at the end.
   WARNING – These files can get large fast. This 30 second sample is around 63Mb.
   The format for this is:
   lynsyn_sampler -d 30

   

   Running the Sampler for 30 Seconds

   Once finished you will get the command line prompt back.