Lynsyn Lite: Difference between revisions
Christopherh (talk | contribs) |
Christopherh (talk | contribs) |
||
| Line 252: | Line 252: | ||
Press '''OK'''.<br> | Press '''OK'''.<br> | ||
The wizard then connects to the Lynsyn Lite and checks what is connected.<br> | The wizard then connects to the Lynsyn Lite and checks what is connected.<br> | ||
[[File:HWManager XVC good result.png| | [[File:HWManager XVC good result.png|frame|left|Virtual Cable: Good Result]] | ||
<div style="clear: both"></div> | <div style="clear: both"></div> | ||
It should show like above, where there is a hardware target listed, and two hardware devices show, the xczu3 and the arm core.<br> | It should show like above, where there is a hardware target listed, and two hardware devices show, the xczu3 and the arm core.<br> | ||
Revision as of 11:16, 1 November 2024
About
The Lynsyn Lite is a dual-purpose card for both power measurement and JTAG communications.
It can monitor voltage and current on three independent sensors, with voltage ranges between 0V and 23V and currents between 0A and 5A.
By default, and as supplied for the V3.1 hardware, the sensors are set to be as the table below:
| Sensor | Current Range | Shunt Resistor | Shunt Size |
|---|---|---|---|
| S1 | 0 - 5 Amps | R4 | 0.025 Ohms |
| S2 | 0 - 2.5 Amps | R5 | 0.05 Ohms |
| S3 | 0 – 1.25 Amps | R6 | 0.1 Ohms |
When in doubt, use S1 as it has the largest current range, but for developments where the current draw is known to be within the lower ranges these would be better to use as they would give a more detailed view of currents drawn at different times.
Full information on the Lynsyn Lite can be found here: https://github.com/EECS-NTNU/lynsyn-host-software/wiki
Software Setup
Windows
(https://github.com/EECS-NTNU/lynsyn-host-software/wiki/Installing-on-Windows)
- Download the pre-built binaries (executables) of the Lynsyn tools. These can be found here:
DOWNLOAD LYNSYN TOOLS V1.3 LINK
(https://github.com/EECS-NTNU/lynsyn-host-software/releases) - Unzip the tools to a location on your computer.
The software tools are not installed and are just run from within this folder so it can be anywhere,
but for ease of use we would suggest C:\lynsyn\. - Install the driver for the card.
-
Connect the Lynsyn Lite to your PC. It gets power over the MicroUSB connection.
-
Open the Zadig application. Your PC may ask if you want to run it (UAC), you do.
It should pop up like this:
zadig application -
From the “Options” menu, select “List All Devices”.
Zadig ListAll The drop-down box in the middle of the application will now be populated. Open this and select the Lynsyn.
Zadig Select Lynsyn Press the button to Install / Reinstall driver.
This may take a few minutes, please wait till you see the pop up saying that the driver was successfully installed:
Zadig Instal Done
-
The Lynsyn Lite should now be ready to use.
Linux
As there are many variations of Linux, this guide is for Ubuntu 22.04.
-
Open a terminal window and update and upgrade
sudo apt-get update && sudo apt-get upgrade -
Install the required dependencies for the Lynsyn project.
sudo apt install build-essential qtbase5-dev libqt5sql5-sqlite libusb-1.0-0-dev git dbus-x11 -
Clone the GitHub repository to your machine.
git clone https://github.com/EECS-NTNU/lynsyn-host-software.git -
Go to the cloned directory
cd lynsyn-host-software/ -
Run the make (Just type “make” – no inverted commas) file to compile the software. It will look like a lot has gone wrong, but as long as it says “Host software compilation successful” at the end, you are OK.
make -
Install the made software by running this command:
sudo make installAgain, it will say a lot, but as long as it shows “Host software compilation successful” and “Software and hardware installed” it is all OK.
You have now built the software packages required for the Lynsyn Lite.
Running the Power Measurement Tools
Windows
Recording a Session
From the command line
- Open a command prompt window and navigate to C:\Lynsyn (or wherever you saved the tools earlier)
-
To start logging a session you need to use the
lynsyn_samplerapplication.
Lynsyn sampler windows
For this simple example we will be just setting to run the application for a 30 second session and saving the data to the default “output.csv” file. To run it for longer or shorter, just change the number at the end.
WARNING – These files can get large fast. This 30 second sample is around 63Mb.
The format for this is:
lynsyn_sampler -d 30
Running the Sampler for 30 Seconds Once finished you will get the command line prompt back.
From the GUI
From the Lynsyn folder you created, launch the “lynsyn_viewer.exe” application.
In the top left corner there are two buttons, “Profile” and “Live”
Pressing the “Live” button brings up a box showing what is happening NOW:
The “Profile” button brings up a box in which you select the length of the sampling you wish to have.
Pressing OK starts the sampling. When complete, “Profiling Done” is shown and the new set of samples are shown in the graph.
Next to these two buttons are three dropdown lists. One selects the parameter shown (Current, Voltage or Power), the second selects which sensor.
In our example, the third is un-used.
You can interact with the graph using your mouse. If you draw a box round a section (left button), it will zoom in. Left clicking will show the values at that point.
Right clicking will zoom out again.
To save this data, go to “File” then “Export CSV.”
Viewing a Session if Recorded from the Command Line or from a Previous Save
If you recorded the session via the command line, from the Lynsyn folder you created, launch the “lynsyn_viewer.exe” application.
When opening it will display the previous result by default. To load the latest set of sampled data, go to “File” then “import CSV.”
Select the file (by default it has “output.csv”) and press OK.
After a few moments it should say “Import Done” and a graph of the recorded session will be shown.
You can interact with the graph using your mouse. If you draw a box round a section (left button), it will zoom in. Left clicking will show the values at that point. Right clicking will zoom out again.
LINUX
Recording a Session
From the command line
- Open a terminal window. As you got, built and installed the files previously, you don't need to be in a specific folder to run the applications.
-
To start logging a session you need to use the
lynsyn_samplerapplication.
Lynsyn sampler windows
For this simple example we will be just setting to run the application for a 30 second session and saving the data to the default “output.csv” file. To run it for longer or shorter, just change the number at the end.
WARNING – These files can get large fast. This 30 second sample is around 63Mb
You need to be sudo so the computer can interact with the Lynsyn Lite..
The format for this is:
sudo lynsyn_sampler -d 30
Running the Sampler for 30 Seconds Once finished you will get the command line prompt back.
From the GUI
Open a terminal window and type:
sudo lynsyn_viewer
You need to be sudo for the computer to interact with the Lynsyn Lite.
This will launch the Lynsyn Viewer application.
Once loaded, in the top left corner there are two buttons, “Profile” and “Live”
Pressing the “Live” button brings up a box showing what is happening NOW:
The “Profile” button brings up a box in which you select the length of the sampling you wish to have.
Pressing OK starts the sampling. When complete, “Profiling Done” is shown and the new set of samples are shown in the graph.
Next to these two buttons are three dropdown lists. One selects the parameter shown (Current, Voltage or Power), the second selects which sensor.
In our example, the third is un-used.
You can interact with the graph using your mouse. If you draw a box round a section (left button), it will zoom in. Left clicking will show the values at that point.
Right clicking will zoom out again.
To save this data, go to “File” then “Export CSV.”
Viewing a Session if Recorded from the Command Line or from a Previous Save
If you recorded the session via the command line and wish to view the results, launch the “lynsyn_viewer” application sudo lynsyn_viewer.
When opening it will display the previous result by default. To load the latest set of sampled data, go to “File” then “import CSV.”
Select the file (by default it has “output.csv”) and press OK.
After a few moments it should say “Import Done” and a graph of the recorded session will be shown.
You can interact with the graph using your mouse. If you draw a box round a section (left button), it will zoom in. Left clicking will show the values at that point. Right clicking will zoom out again.
Using the Lynsyn Lite as an AMD/Xilinx JTAG Cable - Before launching any AMD / Xilinx tools
Windows
From the Lynsyn folder run “lynsyn_xvc.exe”
Windows Firewall may ask if you want to allow this application. Press Allow.
Without that running in the background, the lynsyn will not work as a JTAG pod. Do not close this window.
LINUX
From the terminal run “sudo lynsyn_xvc”
Without that running in the background, the lynsyn will not work as a JTAG pod. Do not close this window.
Using the Lynsyn Lite as an AMD/Xilinx JTAG Cable
This example is for a Xilinx ZU3 FPGA with a built in ARM core.
-
Open Vivado and select “Open Hardware Manager”
Vivado open hardware manager -
Start the Open New Target wizard: “Tools -> Open new Target”
Press “Next” on the first screen.
On the next screen, ensure that Local Server is selected. Press "Next".
Vivado Hardware manager - Local server
-
The next screen will look blank, this is OK.
Press the "Add Xilinx Virtual Cable (XVC)" button.
Add Xilinx Virtual Cable
In the box that pops up, set the host name to “localhost”. Leave the port as 2542.
Virtual Cable Settings Press OK.
The wizard then connects to the Lynsyn Lite and checks what is connected.
Virtual Cable: Good Result It should show like above, where there is a hardware target listed, and two hardware devices show, the xczu3 and the arm core.
Press "Next", then "Finish".
It will then connect and refresh the devices. You can now use it as normal.
Vivado Connected devices
